IKEA BOAXEL 093.926.16 Wall Upright instructions manual

The IKEA BOAXEL 093.926.16 is a wall-mounted upright component designed for the BOAXEL shelving system. It provides sturdy vertical support for shelves, baskets, and other accessories, allowing for customizable storage solutions in various rooms. This manual covers safety warnings, parts identification, step-by-step assembly, mounting instructions, load capacity, and maintenance guidelines.

1. Safety Information 2. Parts Included 3. Tools Required 4. Assembly Instructions 5. Wall Mounting 6. Attaching Shelves & Accessories 7. Weight Capacity 8. Care & Maintenance 9. Troubleshooting 10. Warranty & Support

Safety Information

Read all instructions before assembly and installation.

Parts Included

Check that you have all parts before starting.

Part NameQuantityDescription
Wall Upright (BOAXEL 093.926.16)1Vertical metal rail with pre-drilled holes
Wall Anchors4For securing to wall studs or masonry
Screws4For use with wall anchors
Mounting Template1Paper guide for marking drill holes
Instruction Manual1This document

Note: Shelves, brackets, and other BOAXEL components are sold separately.

Tools Required

Tools not included. You will need:

  1. Stud finder
  2. Pencil
  3. Level
  4. Power drill
  5. Drill bit suitable for your wall type (for anchors)
  6. Phillips screwdriver or drill bit
  7. Hammer (if using hammer-in anchors)
  8. Tape measure

Assembly Instructions

The upright comes pre-assembled. This section covers preparation.

  1. Identify mounting location. Ensure it is free of electrical wires and pipes.
  2. Use a stud finder to locate solid wood studs in the wall. Mark their center.
  3. Decide the height for your upright. The top screw must go into a wall stud.
  4. If mounting between studs or on masonry, use the provided wall anchors at all marked points.

CAUTION! Never rely on drywall alone to support weight. Always anchor into studs or use appropriate masonry anchors.

Wall Mounting

Follow these steps to securely mount the upright to the wall.

  1. Hold the mounting template against the wall at your desired height. Use a level to ensure it is perfectly vertical.
  2. Mark the drill hole positions through the template with a pencil.
  3. Remove the template. Drill holes at the marked points using the correct drill bit size for your anchors.
  4. Insert the wall anchors into the drilled holes. Tap gently with a hammer if needed.
  5. Align the upright's pre-drilled holes with the wall anchors.
  6. Insert the screws through the upright and into the anchors. Tighten securely with a screwdriver or drill.
  7. Use a level again to confirm the upright is straight before fully tightening all screws.

Tip: For maximum stability, at least two screws should be fastened directly into wall studs.

Attaching Shelves & Accessories

Once the upright is securely mounted, you can add BOAXEL components.

  1. Shelf Brackets: Hook the bracket onto the desired slot on the upright. You will hear a click when it's locked in place.
  2. Shelves: Place the shelf onto the installed brackets. Ensure it sits evenly.
  3. Baskets & Hooks: Attach compatible baskets, rods, or hooks to the brackets or directly to the upright slots as per their instructions.
  4. Adjustment: To reposition, lift the bracket slightly to disengage the lock and slide it up or down to a new slot.

WARNING! Do not exceed the maximum weight capacity per bracket or for the entire upright (see Section 7).

Weight Capacity

Adhere to these limits to ensure safety and prevent damage.

Distribute weight evenly. Place heavier items on lower shelves.

Care & Maintenance

To ensure longevity of your BOAXEL upright.

  1. Clean with a soft, damp cloth. Dry immediately.
  2. Do not use abrasive cleaners, scouring pads, or harsh chemicals.
  3. Periodically check that all wall screws are tight (every 6 months).
  4. Do not hang wet items directly on the metal upright to prevent rust.

CAUTION! Do not climb on or use the shelves as a step ladder.

Troubleshooting

ProblemPossible CauseSolution
Upright feels looseScrews not tight; not anchored in studTighten all screws. Remount ensuring at least two screws are in solid studs.
Bracket won't lockNot aligned correctly; debris in slotAlign bracket hook with slot and press down firmly. Clean slots.
Shelf is unevenBrackets not at same height; wall not levelAdjust brackets to same level on both uprights. Use a level on the shelf.
Can't find studStud finder error; non-standard spacingUse manual methods (tapping, measuring from corner). Studs are typically 16" or 24" apart.
Wall material crumblesOld plaster or weak drywallUse specialized toggle bolts or consult a professional for suitable anchors.

Warranty & Support

IKEA BOAXEL products are covered by IKEA's limited warranty. For warranty terms, visit www.ikea.com.

Need help? Visit the IKEA website for assembly guides or contact IKEA customer support in your country.

Recycling: At end of life, disassemble and recycle materials according to local regulations.

IKEA BOAXEL 093.926.16 Wall Upright instructions manual © - All Rights Reserved 2025