IKEA BLODLÖNN 705.423.82 Mirror instructions manual

The IKEA BLODLÖNN 705.423.82 is a wall-mounted mirror designed for bathroom or hallway use. It features a rectangular shape with a simple, clean frame, designed for easy assembly and secure mounting. Below are key sections for safety, parts included, assembly instructions, mounting, care, and warranty information.

1. Parts Included 2. Tools Needed 3. Safety Information 4. Assembly Instructions 5. Mounting to Wall 6. Care & Maintenance 7. Troubleshooting 8. Warranty & Support

Parts Included

Before starting, check that you have all parts listed below.

Part Description	Quantity	Image Ref.
Mirror glass panel	1	A
Frame top section	1	B
Frame bottom section	1	C
Frame side sections (left & right)	2	D
Wall mounting brackets	2	E
Screws and wall plugs	Set	F
Allen key	1	G
Instruction manual	1	-

Tools Needed

You will need the following tools (not included):

Phillips screwdriver
Drill with appropriate drill bit for your wall type
Level
Pencil
Tape measure

Safety Information

WARNING! To prevent serious injury:

This mirror is heavy. Always assemble and mount with the help of another person.
Ensure the wall is suitable for the weight. Use appropriate wall anchors for your wall type (drywall, plaster, concrete).
Do not mount above bathtub or in areas where it may be exposed to direct, high-pressure water jets.
Keep children away during assembly and mounting.
Check all screws and brackets are tight before letting go of the mirror.

Assembly Instructions

Follow these steps to assemble the mirror frame.

Prepare workspace: Lay the mirror glass panel on a soft, flat surface (e.g., carpet or blanket) to avoid scratches.
Attach side frames: Take the left side frame (D) and align it with the top edge of the mirror. Insert and tighten the provided screws using the Allen key (G). Repeat for the right side.
Attach top and bottom frames: Place the top frame (B) and bottom frame (C) onto the assembled sides. Secure with screws at each corner.
Check alignment: Ensure the frame is square and all joints are flush. Tighten all screws firmly but do not overtighten.

CAUTION! Handle mirror glass with care. Wear gloves to protect edges.

Mounting to Wall

Mount the assembled mirror securely to the wall.

Locate studs: Use a stud finder to locate wall studs. Mark their positions lightly with a pencil.
Position brackets: Hold the mirror against the wall at the desired height. Mark the positions for the wall mounting brackets (E) on the wall through the bracket holes.
Drill holes: Drill holes at the marked points using a drill bit suitable for your wall anchors.
Insert wall plugs: Tap the provided wall plugs into the drilled holes.
Secure brackets: Screw the mounting brackets to the wall using the provided screws. Ensure they are level and tight.
Hang mirror: With help, lift the mirror and hook it onto the mounted brackets. Ensure it is securely seated.
Final check: Gently test the mirror for stability. Use a level to confirm it is straight.

Tip: For solid walls (concrete/brick), you may need to purchase appropriate anchors separately.

Care & Maintenance

To keep your mirror clean and in good condition:

Use a soft, lint-free cloth or microfiber cloth.
For cleaning, lightly dampen the cloth with water or a mild glass cleaner. Do not spray directly onto the mirror.
Wipe gently in a circular motion. Dry with a separate dry cloth to prevent streaks.
Avoid abrasive cleaners, scouring pads, or harsh chemicals.
Do not use excessive water near the frame joints.

CAUTION! Never use sharp objects or excessive force on the mirror surface.

Troubleshooting

Issue	Possible Cause	Solution
Mirror feels loose on wall	Brackets not tight; wall anchors insufficient	Check and tighten all screws. Ensure wall anchors are rated for the mirror's weight. Remount into studs if possible.
Frame pieces don't align	Screws not fully tightened; parts misassembled	Disassemble and reassemble in correct order per steps. Ensure all parts are oriented correctly.
Mirror is not level	Wall brackets installed unevenly	Loosen bracket screws slightly, adjust using a level, then retighten.
Scratches on glass	Improper handling during assembly	Prevent further damage by handling edges only. Minor scratches may not be removable.
Screws missing or stripped	Packaging error or over-tightening	Contact IKEA customer service for replacement parts.

Warranty & Support

This IKEA product is covered by a limited warranty. Refer to the IKEA warranty terms included in the packaging or available at IKEA stores.

For assistance:

Visit the IKEA website: www.ikea.com
Contact IKEA customer support at 1-888-888-4532
Visit your local IKEA store with your receipt and product information.

Keep your receipt as proof of purchase.