IKEA BETSÖ 094.136.28 Umbrella Frame instructions manual

The IKEA BETSÖ 094.136.28 is a freestanding umbrella frame designed for outdoor use with a standard market umbrella (not included). It features a sturdy steel construction, a convenient crank handle for easy opening and closing, a tilt function for sun angle adjustment, a stable weighted base, and a weather-resistant powder-coated finish. Below are key sections for safety, assembly, installation, operation, care, and troubleshooting.

1. Parts & Tools Included 2. Safety Information 3. Assembly Instructions 4. Installation & Setup 5. Operation 6. Care & Maintenance 7. Specifications 8. Troubleshooting 9. Warranty & Support

Parts & Tools Included

Before assembly, verify all parts are present. Key components: Main Pole, Base Frame, Weight Plates (or sand/water fill option), Crank Handle Assembly, Tilt Mechanism, Hardware Pack, Allen Key.

Part Name	Quantity	Description
Main Pole	1	Central vertical support tube
Base Frame	1	Bottom support structure
Weight Plates	4	Concrete plates for stability (if included)
Crank Handle	1	For opening/closing umbrella
Tilt Mechanism	1	Allows umbrella angle adjustment
Hardware Pack	1	Screws, bolts, washers
Allen Key	1	For assembly

Safety Information

WARNING! Read all instructions before assembly and use.

Stability: Ensure the base is fully weighted (with plates, sand, or water) before inserting an umbrella. An unweighted frame can tip over, causing injury or damage.
Weather: Close and tilt the umbrella in strong winds, rain, or snow. Do not leave it open unattended in severe weather.
Placement: Place on a flat, stable surface. Keep away from overhead power lines, trees, or structures.
Handling: The frame and weighted base are heavy. Use proper lifting techniques or get assistance.
Children: Do not allow children to play on or operate the crank/tilt mechanisms unsupervised.

Assembly Instructions

Estimated assembly time: 30-45 minutes. Requires two people for some steps.

Prepare Base: If using weight plates, place them into the compartments of the base frame. If using sand/water, locate the fill caps but do not fill until the frame is in its final position.
Attach Main Pole: Insert the bottom end of the main pole into the center socket on the base frame. Secure with the provided large bolt and washer, tightening with the Allen key.
Install Tilt Mechanism: Slide the tilt mechanism collar onto the main pole at the designated height. Secure it with the set screws using the Allen key. Ensure it moves smoothly.
Attach Crank Handle: Locate the crank gearbox near the top of the main pole. Align the crank handle shaft and insert it, securing it with the retaining pin or screw from the hardware pack.
Final Check: Tighten all bolts and screws. Ensure the pole is vertical and the base is level.

Tip: Do not overtighten screws into the aluminum/steel parts.

Installation & Setup

Choose Location: Select a flat, firm area (patio, deck, garden). Ensure there is ample clearance for the open umbrella and tilt function.
Position Frame: Move the assembled frame to the desired location. Use a level to check that the base is flat.
Add Weight:
- Plates: Ensure all plates are correctly seated.
- Sand/Water: Fill the base compartments through the fill caps. Do not overfill. Secure caps tightly.
Insert Umbrella: Open your market umbrella slightly to insert the pole. Slide the umbrella pole down through the tilt mechanism and into the main pole of the frame until it rests securely. Tighten the tilt mechanism knob to hold the umbrella pole firmly.

CAUTION! The frame must be weighted before use. An empty base provides minimal stability.

Operation

Opening/Closing: Turn the crank handle clockwise to open the umbrella, counter-clockwise to close it. Do not force the crank if it jams.

Tilting: To adjust the angle, loosen the tilt knob on the mechanism, tilt the umbrella pole to the desired position, and re-tighten the knob firmly.

Securing for Wind: In breezy conditions, close the umbrella and use the provided strap or tie to secure the closed canopy.

Care & Maintenance

Unplug? N/A. For cleaning and storage.

Cleaning: Wipe the steel frame with a soft, damp cloth. Use mild soap if needed. Dry thoroughly. Do not use abrasive cleaners or solvents.
End of Season: Remove the umbrella. Clean and dry the frame. If possible, store indoors in a dry place. If storing outdoors, cover with a waterproof cover.
Sand/Water Base: If filled, empty the base before winter to prevent freezing and cracking.
Moving: Empty sand/water or remove weight plates before attempting to move the frame.

CAUTION! Do not use a pressure washer on the crank mechanism or bearings.

Specifications

Product Name: BETSÖ Umbrella Frame
Article Number: 094.136.28
Material: Steel, powder-coated finish.
Umbrella Pole Fit: Fits standard market umbrellas with a pole diameter of approximately 38-50mm (1.5-2 inches).
Base Weight Capacity: Holds up to 50 kg (110 lbs) of sand/water or included plates.
Tilt Function: Yes, multiple angles.
Crank Operation: Yes, manual.
Intended Use: Outdoor residential use.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Frame wobbles or tips	Base not weighted enough or on uneven ground.	Add more weight (sand/water/plates). Move to a flat, solid surface.
Crank handle is stiff/jammed	Debris in gears, lack of lubrication, or umbrella is stuck.	Open/close umbrella manually slightly to relieve pressure. Check for obstructions. Apply silicone-based lubricant to gears if needed.
Umbrella pole slips or won't stay tilted	Tilt mechanism knob is not tight enough.	Tighten the tilt knob firmly. Ensure the umbrella pole is the correct diameter for the clamp.
Rust spots appearing	Finish scratched or exposed to constant moisture.	Clean area, dry thoroughly, and touch up with matching outdoor paint to prevent spread.
Base leaking (if water-filled)	Fill cap not secure or seal damaged.	Ensure cap is tight. Check seal for cracks. Empty base if leak persists.

Warranty & Support

Refer to the IKEA warranty card included with your purchase for specific terms and duration. This product is designed for residential use.

For missing parts or assembly support: Contact IKEA customer service with your article number (094.136.28) and receipt.

IKEA Customer Service: Visit www.ikea.com or your local IKEA store.

Recycling: At end of life, disassemble and recycle materials according to local regulations. Steel is widely recyclable.