IKEA BEKANT 002.632.18 Underframe instructions manual

The IKEA BEKANT 002.632.18 Underframe is a sturdy, height-adjustable desk frame designed for stability and ergonomic flexibility. It supports various tabletop sizes, features electric height adjustment, a cable management tray, and a robust steel construction. Below are key sections for safety, assembly, installation, operation, maintenance, and troubleshooting.

Product Overview

Key components: Steel underframe with electric lift columns, Control panel with up/down buttons, Cable management tray, Mounting brackets for tabletop, Power supply unit.

Safety Instructions

Read all instructions before assembly and use.

1. Weight Limit: Do not exceed the maximum load capacity of 110 lbs (50 kg) for the frame plus tabletop weight.
2. Electrical Safety: Use only the provided power supply. Ensure power cord is not pinched or damaged.
3. Stability: Assemble on a flat, stable surface. Ensure all fasteners are tightened securely.
4. Pinch Points: Keep hands and fingers clear of moving parts during height adjustment.
5. Two-Person Lift: The frame is heavy; use two people for handling to avoid injury.

WARNING! Disconnect power before performing any maintenance or troubleshooting. Do not use if any part is damaged.

Package Contents

Unpack and verify all parts are present before starting assembly.

• Underframe (left and right sides pre-assembled)
• Electric lift columns (2)
• Crossbar
• Cable management tray
• Control panel with cable
• Mounting brackets and hardware pack
• Power supply unit with cable
• Assembly tool (Allen key)
• Instruction manual (this document)

Note: Contact IKEA if any parts are missing or damaged.

Assembly Instructions

Estimated assembly time: 30-45 minutes. Recommended: Two people.

1. Prepare Area: Lay out all parts on a clean, soft surface to prevent scratches.
2. Attach Crossbar: Connect the crossbar to the left and right sides of the underframe using the provided bolts. Tighten securely with the Allen key.
3. Install Cable Tray: Snap the cable management tray onto the crossbar.
4. Mount Lift Columns: Attach the electric lift columns to each side of the underframe. Ensure they are oriented correctly (motor at the bottom).
5. Connect Cables: Route the cables from the control panel and power supply through the cable tray. Connect them to the motor columns as per the diagram.
6. Attach Control Panel: Mount the control panel to the underside of the tabletop (or designated bracket) using the provided screws.
7. Final Check: Ensure all connections are secure and no cables are pinched.

Installation & Setup

Attaching your tabletop and initial power-up.

1. Position Tabletop: Place your tabletop upside down on a protected surface.
2. Position Underframe: Place the assembled underframe centered on the tabletop. Ensure the control panel cable can reach its mounting location.
3. Attach Brackets: Use the mounting brackets and screws to secure the underframe to the tabletop. Follow the pre-drilled guide holes or recommended spacing.
4. Flip Desk: Carefully flip the entire desk upright with the help of a second person.
5. Power Connection: Plug the power supply into a grounded 120V AC outlet. The control panel may light up.
6. Test Movement: Press the up and down buttons to ensure smooth operation across the full height range.

CAUTION! Ensure the desk is clear of obstructions before testing height adjustment.

Operation & Adjustment

Using the electric height adjustment.

Control Panel: Typically features UP and DOWN buttons. Some models may include memory preset buttons (M1, M2, M3).

1. Basic Adjustment: Press and hold the UP or DOWN button to raise or lower the desk. Release to stop.
2. Setting Memory Presets (if applicable):
   • Adjust the desk to your desired height.
   • Press and hold the desired M button (e.g., M1) for 3 seconds until it beeps.
   • Repeat for other presets (M2, M3).
3. Recall Preset: Briefly press the corresponding M button to automatically move the desk to the saved height.
4. Height Range: The desk typically adjusts between approximately 22" and 48" (56 cm - 122 cm) from the floor to the underside of the tabletop.

Tip: Avoid placing excessive weight on the desk while adjusting height.

Technical Specifications

• Model: BEKANT Underframe 002.632.18
• Material: Steel, Polypropylene plastic (cable tray)
• Color: Black/Brown (as per variant)
• Adjustment Type: Electric, dual-motor
• Height Range: Approx. 22" - 48" (56 - 122 cm)
• Max Load Capacity: 110 lbs (50 kg) including tabletop
• Recommended Tabletop Size: Up to 63" x 31 ½" (160cm x 80cm)
• Power Supply: Input: 120V AC, 60Hz; Output: 24V DC
• Noise Level: < 50 dB during operation

Care & Maintenance

Unplug the desk before any cleaning or maintenance.

1. Cleaning: Wipe the steel frame with a soft, dry cloth. For stains, use a damp cloth with mild soap. Do not use abrasive cleaners.
2. Cable Management: Periodically check the cable tray and ensure cables are not tangled or straining connections.
3. Fastener Check: Every 6 months, check that all screws and bolts are tight.
4. Mechanical Inspection: Listen for unusual noises during operation. Ensure movement remains smooth.

CAUTION! Do not spray liquids directly onto the frame or control panel. Never immerse any part in water.

Troubleshooting

Reset: Unplug the power supply for 60 seconds, then plug back in to reset the control unit.

Warranty & Support

This IKEA BEKANT underframe is covered by a limited warranty. Refer to the IKEA warranty document included in the original packaging for specific terms and duration.

For Support:
IKEA Customer Service: 1-888-888-4532
IKEA Website: www.ikea-usa.com
Visit the "Assembly & Support" section for this product using the 8-digit article number (002.632.18).

Recycling: At end of life, dispose of electronic components according to local regulations. Do not dispose of with household waste.