IKEA BARLAST 704.378.14 Floor Lamp instructions manual

The IKEA BARLAST 704.378.14 is a modern floor lamp featuring a sturdy metal base, an adjustable shade for directional lighting, an integrated on/off switch on the cord, and uses a maximum 13W E26/E27 LED bulb (not included). Designed for indoor residential use. Below are key sections for safety, assembly, operation, care, and troubleshooting.

1. Package Contents & Tools Needed 2. Safety Instructions 3. Assembly Steps 4. Specifications 5. Operation & Adjustment 6. Bulb Replacement 7. Care & Maintenance 8. Troubleshooting 9. Warranty & Support

Package Contents & Tools Needed

Before assembly, check that all parts are present and undamaged.

Part Description	Quantity	Image Ref.
Base (metal, weighted)	1	A
Center pole (main stem)	1	B
Adjustable shade with bracket	1	C
Hardware pack (screws, washers)	1 set	D
Cord with integrated switch	1	E
Instruction manual	1	-

Tools needed: Phillips screwdriver (not included).

Safety Instructions

WARNING! To reduce risk of fire, electric shock, or injury:

Read all instructions before assembly and use.
Unplug lamp before assembly, cleaning, or bulb replacement.
Use only with a maximum 13W E26/E27 LED bulb. Do not exceed wattage.
This lamp is for indoor use only. Keep away from water and damp locations.
Do not operate with a damaged cord or plug. If damaged, discontinue use.
Ensure the lamp is placed on a stable, level surface to prevent tipping.
Allow bulb to cool before touching. LED bulbs may become warm during use.
Do not cover the lamp or shade with any material.
This is not a toy. Keep out of reach of children.

Assembly Steps

Follow steps in order. Assembly requires approximately 15-20 minutes.

Attach Base to Pole: Insert the center pole (B) into the hole on the base (A). Secure using the provided screw and washer from pack (D). Tighten firmly with a screwdriver.
Route the Cord: Feed the cord (E) up through the center of the pole (B). Ensure it is not pinched or twisted.
Attach the Shade: Position the adjustable shade (C) onto the top of the pole. Align the holes and secure with the remaining screws from pack (D). Do not overtighten.
Final Check: Gently shake the assembled lamp to ensure all connections are tight. Adjust the shade to your desired angle.

CAUTION! Do not plug in the lamp until assembly is complete and you are ready to install the bulb.

Specifications

Product Name: BARLAST
Article Number: 704.378.14
Type: Floor Lamp, Adjustable
Material: Base/Pole: Steel, Shade: Aluminum/Plastic
Color: Black
Max. Bulb Wattage: 13W LED
Bulb Base: E26/E27 (Standard)
Power Cord Length: Approx. 6 ft (1.8 m)
Switch Type: In-line cord switch
Dimensions (HxW): Approx. 55" H x 12" W (140 cm x 30 cm)
Weight: Approx. 8.8 lbs (4 kg)
Intended Use: Indoor, residential

Operation & Adjustment

Once assembled and bulb is installed:

Turning On/Off: Use the rocker switch located on the power cord.
Adjusting Light Direction: The shade can be tilted up or down. Gently grasp the edge of the shade and adjust to direct light where needed.
Positioning: Place the lamp on a flat, stable surface near a power outlet. Ensure the cord is not a tripping hazard.

Tip: For ambient lighting, point the shade upward. For task lighting (reading, work), tilt the shade downward.

Bulb Replacement

WARNING! UNPLUG THE LAMP FIRST. Allow old bulb to cool completely.

Unplug the lamp from the electrical outlet.
Allow any existing bulb to cool for at least 5 minutes.
Gently grasp the bulb and turn it counterclockwise to remove it from the socket.
Insert a new LED bulb with an E26/E27 base. Do not exceed 13W.
Turn the bulb clockwise until it is snug. Do not overtighten.
Plug the lamp back in and test with the switch.

Note: Using a bulb with higher wattage than recommended may cause overheating and damage.

Care & Maintenance

To keep your lamp in good condition:

Cleaning: Always unplug the lamp. Wipe the metal and plastic surfaces with a soft, dry or slightly damp cloth. Do not use abrasive cleaners or chemicals.
Storage: If storing, disassemble in reverse order of assembly and pack in original box if possible. Store in a cool, dry place.
Inspection: Periodically check that all screws are tight and the cord is not frayed or damaged.

CAUTION! Never immerse the lamp, cord, or plug in water or other liquids.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Lamp does not turn on	Not plugged in / Bulb burnt out / Switch off	Plug into outlet. Replace bulb. Ensure cord switch is in the "ON" position.
Lamp flickers	Loose bulb / Faulty bulb	Turn off, unplug, and ensure bulb is screwed in tightly. Try a different bulb.
Lamp is wobbly	Assembly screws loose / Uneven surface	Turn off and unplug. Tighten all assembly screws. Place on a level surface.
Shade does not stay in position	Pivot joint needs tightening	Carefully tighten the screw at the shade's pivot point. Do not overtighten.
Overheating	Bulb wattage too high / Ventilation blocked	Use only a 13W max LED bulb. Ensure shade vents are not covered.

Warranty & Support

This IKEA product is guaranteed under the terms of IKEA's limited warranty. Please refer to your IKEA guarantee document for full details on coverage and duration.

For Assembly Help or Missing Parts: Visit the IKEA website or contact your local IKEA store.

IKEA Customer Support: Visit www.ikea.com for your country or call the number listed on your receipt.

Recycling: At end of life, do not dispose of with household waste. Recycle according to local regulations for electronic/electrical equipment (WEEE).