IKEA BARKABODA 103.314.72 Countertop instructions manual

The IKEA BARKABODA 103.314.72 is a solid oak veneer countertop designed for kitchen and work surfaces. It features a durable, pre-finished surface resistant to everyday wear, is compatible with IKEA cabinet systems (like SEKTION/METOD), requires assembly and installation, includes pre-drilled holes for mounting, and needs sealing of cut edges for moisture protection. Below are key sections for safety, features, preparation, assembly, installation, care, and troubleshooting.

Product Overview & Features

Key components: Solid oak veneer countertop, mounting brackets, installation hardware, edge sealing strips (if included).

Safety Instructions

Read all instructions before assembly. Ensure safe handling and installation.

1. Lifting: Countertop is heavy; lift with care using two people to avoid back injury.
2. Stable surface: Install on level, securely mounted cabinets only.
3. Tools: Use appropriate safety equipment (gloves, eye protection) when cutting or drilling.
4. Ventilation: Ensure good ventilation if applying sealant or adhesive.
5. Children: Keep away from assembly area to prevent accidents.

WARNING! Do not stand or sit on the countertop. Ensure cabinets are level and securely attached to wall.

Tools & Materials Needed

Gather tools before starting assembly.

1. Phillips screwdriver or cordless drill with screwdriver bit.
2. Level (at least 24 inches).
3. Tape measure and pencil.
4. Clamps (for securing during installation).
5. Circular saw or jigsaw with fine-tooth blade (if cutting to size).
6. Sandpaper (120-grit and 220-grit).
7. Edge sealant or IKEA sealing strips (for cut edges).
8. Cleaning cloth.

CAUTION! Use sharp blades for clean cuts; dull blades can damage veneer.

Specifications

• Article Number: 103.314.72
• Material: Oak veneer, Particleboard, Acrylic lacquer
• Thickness: 1 1/2" (3.8 cm)
• Standard Lengths: 74", 98" (188 cm, 246 cm) – confirm product label
• Depth: 25 5/8" (65 cm)
• Weight: Approximately 55-85 lbs (25-39 kg) depending on length
• Max Overhang: 10" (25 cm) without additional support
• Load Capacity: Evenly distributed weight; avoid point loads
• Care Instructions: Wipe with damp cloth; avoid abrasive cleaners
• Warranty: Refer to IKEA limited warranty

Preparation & Planning

Measure cabinet layout and plan countertop placement.

1. Measure cabinet run: Ensure total length matches countertop or plan for cutting.
2. Check level: Cabinets must be level and securely fastened to wall.
3. Plan seams: For multiple sections, plan seam location (avoid over sink or cooktop).
4. Cutouts: Mark sink, cooktop, or faucet cutouts on underside before installation.
5. Dry fit: Place countertop on cabinets (with help) to check fit before final mounting.

Tip: Allow countertop to acclimate to room temperature and humidity for 48 hours before installation.

Assembly Instructions

Attach mounting brackets and prepare countertop.

1. Identify pre-drilled holes: Located on underside of countertop for bracket attachment.
2. Attach brackets: Use provided screws to secure brackets to underside at marked locations.
3. Align brackets: Ensure brackets align with cabinet frame top rails.
4. Join sections (if applicable): Use connector bolts and brackets provided for multi-piece tops.
5. Seal cut edges: If countertop was cut, apply sealant or attach sealing strips immediately.

WARNING! Do not overtighten screws into particleboard core to avoid stripping.

Installation Guide

Mount countertop to cabinets.

1. Position countertop: With help, lift and place countertop onto cabinets, aligning brackets with cabinet frames.
2. Secure from below: From inside cabinets, screw up through cabinet rails into brackets.
3. Check level: Place level across surface; adjust if necessary with shims under countertop.
4. Connect sections: Tighten connector bolts evenly for seamless join.
5. Install end caps or edge strips: Apply to exposed ends if provided.
6. Make cutouts: Use jigsaw to cut openings for sink/cooktop if not pre-cut.

CAUTION! Lift with legs, not back. Ensure cabinets are securely anchored to wall studs.

Sealing & Finishing

Protect cut edges from moisture.

1. Sand cut edges: Smooth with 120-grit then 220-grit sandpaper.
2. Clean: Wipe away dust with damp cloth, let dry.
3. Apply sealant: Use IKEA recommended sealant or beeswax, following product instructions.
4. Attach sealing strips: For IKEA strips, peel backing and press firmly onto edge.
5. Allow to cure: Let sealant dry completely (per manufacturer's time) before use.

Important: Unsealed edges will swell if exposed to moisture. Reapply sealant periodically.

Care & Maintenance

Clean with damp cloth; avoid harsh chemicals.

Daily: Wipe with soft, damp cloth. Dry immediately.

Stains: Use mild soap solution; rinse and dry.

Scratches: Light scratches can be minimized with IKEA touch-up pen or wax.

Heat protection: Always use trivets or hot pads; never place hot pans directly on surface.

Moisture: Wipe spills promptly; avoid standing water, especially near seams or edges.

CAUTION! Do not use abrasive pads, scouring powders, or strong solvents (acetone, bleach).

Warranty & Support

IKEA limited warranty applies. See IKEA warranty booklet for details.

Warranty coverage: Manufacturing defects under normal use.

Not covered: Damage from improper installation, lack of sealing, misuse, accidents, or modifications.

Support: For missing parts or assembly help, contact IKEA customer service or visit www.ikea.com.

Spare parts: Brackets, screws, connectors available through IKEA.

Recycling: Dispose of packaging responsibly; countertop can be recycled per local regulations.

Troubleshooting

Professional help: For complex installations or modifications, consult a qualified carpenter.

IKEA Support: 1-888-888-4532 (IKEA-USA) or visit www.ikea.com for your country.