IKEA AXSTAD 904.683.95 Cover Panel instructions manual

The IKEA AXSTAD 904.683.95 is a cover panel designed for kitchen cabinets, part of the AXSTAD series. It features a durable finish, pre-drilled holes for handles, and is compatible with various IKEA cabinet frames. Below are key sections for safety, features, installation, setup, care, and troubleshooting.

Features at a Glance

Key components: Cover panel, pre-drilled handle holes, mounting brackets (if included), and installation hardware.

Package Contents

Unpack and verify all parts before installation.

1. Cover panel (1 piece)
2. Mounting brackets (4 pieces, if included)
3. Screws (8 pieces, size 4x30mm)
4. Handle screws (4 pieces, size 5x25mm)
5. Instruction manual (this document)

WARNING! Check for damage during shipping. Do not install damaged parts.

Tools Required

Gather tools before starting installation.

1. Phillips screwdriver (size #2)
2. Drill with 4mm drill bit (if pre-drilling required)
3. Level
4. Tape measure
5. Pencil for marking
6. Safety glasses

CAUTION! Use appropriate safety gear when drilling or handling panels.

Installation Instructions

Follow steps in order for proper installation.

1. Prepare cabinet frame: Ensure frame is level and securely mounted to wall.
2. Attach hinges: Mount hinges to cabinet frame according to hinge instructions.
3. Position panel: Align panel with frame, ensuring even gaps on all sides.
4. Secure brackets: Attach mounting brackets to panel using provided screws.
5. Connect to hinges: Hook panel brackets onto hinges and tighten adjustment screws.
6. Check alignment: Open and close panel to ensure smooth operation.

Tip: Have a second person assist with holding panel during installation.

Mounting to Cabinet Frame

Detailed steps for attaching panel to frame.

1. Mark hinge positions on frame using template (if provided).
2. Drill pilot holes for hinge screws at marked positions.
3. Screw hinges firmly into frame.
4. Attach mounting brackets to rear of panel at corresponding positions.
5. Lift panel and engage brackets with hinges.
6. Tighten hinge adjustment screws to secure panel.
7. Test door swing and adjust as needed.

WARNING! Ensure frame is securely anchored to wall studs to support panel weight.

Handle Attachment

Attaching handles to pre-drilled holes.

1. Align handle with pre-drilled holes on panel front.
2. Insert handle screws through back of panel into handle.
3. Tighten screws evenly until handle is secure but not over-tightened.
4. Check that handle is level and firmly attached.

Note: Handle screws are included; handles sold separately.

Adjustments & Alignment

Fine-tuning panel position and operation.

• Vertical adjustment: Loosen hinge screws, move panel up/down, retighten.
• Horizontal adjustment: Adjust hinge side-to-side for even gap with adjacent panels.
• Depth adjustment: Set panel flush with frame or adjust reveal as desired.
• Closing force: Adjust hinge tension for smooth closing (if hinge supports this feature).

Tip: Make small adjustments and test operation after each change.

Care & Cleaning

Maintaining your cover panel.

1. Use soft, damp cloth with mild detergent for cleaning.
2. Wipe dry immediately to prevent moisture damage.
3. Avoid abrasive cleaners, scouring pads, or harsh chemicals.
4. Do not use excessive water or steam cleaners.

CAUTION! Never use solvents or ammonia-based cleaners on the surface.

Safety Information

Important safety precautions.

• Install according to instructions only.
• Ensure cabinet frame is securely mounted to wall studs.
• Use appropriate tools and safety equipment.
• Keep children away during installation.
• Do not exceed weight limits of cabinet system.
• Check periodically for loose screws or brackets.

WARNING! Improper installation can cause injury or damage.

Troubleshooting

Support: For additional help, contact IKEA customer service or visit www.ikea.com.