IKEA ARÖD 905.218.97 Work Lamp instructions manual

The IKEA ARÖD 905.218.97 is a versatile work lamp designed for focused lighting on desks, workbenches, or reading areas. It features an adjustable arm and head for precise light direction, an energy-efficient LED light source, an integrated on/off switch, and a stable clamp or base for secure mounting. Below are key sections for safety, assembly, operation, care, and troubleshooting.

1. Features at a Glance 2. Assembly Instructions 3. Installation & Mounting 4. Specifications 5. Controls and Operation 6. Adjusting the Lamp 7. Replacing the Light Source 8. Safety Information 9. Care & Cleaning 10. Warranty & Support 11. Troubleshooting

Features at a Glance

Key components: Adjustable metal arm, Rotatable lamp head, LED light module, On/Off switch, Mounting clamp or base, Power cord.

Feature	Description
Adjustable arm	Allows height and reach adjustment for optimal positioning
Rotatable lamp head	Provides 360-degree rotation for precise light direction
LED light source	Energy-efficient, long-lasting, and cool-to-touch operation
Integrated On/Off switch	Conveniently located on the lamp head or cord
Mounting clamp	Securely attaches to desks, shelves, or work surfaces (up to [specify thickness])
Stable base (if applicable)	Provides a weighted, non-slip footing for tabletop use
Power cord	Standard plug for 120V AC outlets
Joints	Friction-based or screw-tightened for holding position

Assembly Instructions

Unpack all parts and check against the included parts list. Assemble on a clean, flat surface.

Attach the arm: Insert the arm into the base or clamp assembly. Tighten the securing screw or knob firmly.
Attach the lamp head: Connect the lamp head to the end of the arm. Ensure the joint is secure and allows rotation.
Route the cord: Guide the power cord along the arm, using any clips or channels provided, to keep it tidy.
Final check: Ensure all screws and joints are tight, but do not over-tighten.

WARNING! Assemble the lamp on a stable surface. Do not force parts together. If a part is damaged or missing, do not use the lamp.

Installation & Mounting

Choose a suitable location near a power outlet and on a stable surface.

For Clamp Mounting: Open the clamp, position it on the edge of your desk or shelf (ensure thickness is within clamp capacity), and tighten the screw firmly until the lamp is secure and does not wobble.
For Base Mounting: Place the weighted base on a flat, stable surface. Ensure the lamp is not near the edge where it could be knocked over.
Power Connection: Plug the power cord into a standard 120V AC wall outlet.

CAUTION! Do not mount the clamp on unstable, fragile, or overheated surfaces. Ensure the lamp is securely fastened and the cord is not pinched or a tripping hazard.

Specifications

Model: ARÖD 905.218.97
Light Source: Integrated LED module.
Color Temperature: [e.g., 4000K Cool White]
Luminous Flux: [e.g., 400 lumens]
Power Consumption: [e.g., 5W]
Input Voltage: 120V AC, 60Hz.
Arm Reach: Adjustable up to [e.g., 24 inches].
Clamp Capacity: Fits surfaces up to [e.g., 2 inches] thick.
Materials: Steel, Aluminum, Plastic.
Weight: [e.g., 2.2 lbs]

Controls and Operation

Power Switch: Located on the lamp head or inline on the cord. Press or slide to turn the lamp On or Off.

Adjustment: The lamp is designed for manual adjustment. Grip the arm or head and position it as needed. The joints will hold their position once released.

Note: This model does not feature a dimmer. The LED provides a fixed level of brightness.

Adjusting the Lamp

Positioning: Grip the arm firmly near a joint. Move it to the desired height and angle.
Directing Light: Hold the lamp head and rotate or tilt it to focus the light exactly where needed.
Holding Power: If the arm becomes loose over time, locate the adjustment screw or knob at the joint and tighten it slightly. Do not over-tighten.

Tip: Adjust the lamp while it is cool to the touch. Avoid making sharp bends in the arm or forcing it beyond its natural range of motion.

Replacing the Light Source

Important: The ARÖD lamp uses an integrated, non-user-replaceable LED module. If the light fails, the entire lamp head may need to be serviced or replaced.

Unplug the lamp from the electrical outlet and allow it to cool completely.
DO NOT attempt to open the lamp head. This could damage the unit and void the warranty.
For service, contact IKEA customer support (see Warranty & Support section).

WARNING! Never attempt to replace or repair the LED module yourself. There are no user-serviceable parts inside. Risk of electric shock.

Safety Information

Read all instructions before use.

Use only with 120V AC power.
Unplug before cleaning, adjusting, or when not in use for extended periods.
Do not use outdoors or in damp/wet locations.
Do not cover the lamp or place flammable materials near it.
This lamp is not a toy. Keep away from children.
Do not look directly into the LED light source.
Ensure the clamp is securely fastened to prevent the lamp from falling.

Care & Cleaning

Unplug the lamp and allow it to cool before cleaning.

Wipe the metal and plastic surfaces with a soft, dry or slightly damp cloth.
Do not use abrasive cleaners, solvents, or chemicals.
Ensure no moisture enters the lamp head or switch.

CAUTION! Never immerse the lamp in water or other liquids. Do not spray cleaning agents directly onto the lamp.

Warranty & Support

This IKEA product is covered by a limited warranty. Refer to the IKEA warranty document included with your purchase or available at IKEA stores for full terms and conditions.

For product support, assembly help, or warranty claims:

Visit: www.ikea.com
Contact your local IKEA store.
Refer to your original receipt for proof of purchase.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Lamp does not turn on	No power / Loose connection	Check if the outlet is working. Ensure the plug is fully inserted. Check the On/Off switch.
Lamp arm is loose, won't hold position	Joint adjustment needed	Locate the adjustment screw or knob at the loose joint and tighten it slightly. Do not over-tighten.
Lamp flickers	Faulty connection / LED issue	Ensure the plug is secure. Try a different outlet. If problem persists, the LED module may be faulty.
Clamp does not grip securely	Surface too thick or clamp not tightened	Ensure surface thickness is within specifications. Tighten the clamp screw firmly.
Lamp gets warm	Normal operation	Some warmth is normal during use. It should not become excessively hot to the touch.

Disposal: At end of life, dispose of this electronic product according to local regulations. Do not dispose with household waste.