IKEA ARÖD 905.140.57 Floor Lamp instructions manual

The IKEA ARÖD 905.140.57 is a modern floor lamp featuring a minimalist design with a metal base and a fabric shade. It provides ambient lighting suitable for living rooms, bedrooms, or reading corners. The lamp requires assembly and uses a standard E27 bulb (max 13W LED or equivalent, not included). Below are key sections for safety, assembly instructions, usage, care, and troubleshooting.

1. Safety Information 2. Package Contents 3. Assembly Instructions 4. Specifications 5. Installation & Setup 6. Operation 7. Care & Maintenance 8. Troubleshooting 9. Warranty & Support

Safety Information

Read all instructions before assembly and use.

Warning	Description
Electrical Safety	Use only with E27 bulb max 13W LED. Do not exceed wattage.
Placement	Place on stable, level surface away from heat sources and water.
Children	Keep out of reach of young children during assembly and use.
Cord Management	Do not pinch or damage cord; keep away from walkways.
Bulb Replacement	Ensure lamp is unplugged and bulb is cool before replacing.

Package Contents

Unpack and verify all parts are included.

Metal base (1 piece)
Fabric shade (1 piece)
Metal stem (1 piece)
Socket assembly with cord (1 set)
Hardware pack (screws, washers)
Instruction manual (this document)

NOTE: Contact IKEA if any parts are missing or damaged.

Assembly Instructions

Estimated assembly time: 15-20 minutes. Tools required: Phillips screwdriver (not included).

Prepare workspace: Clear area and lay out all parts.
Attach base to stem: Align stem with base hole and secure with provided screw.
Install socket: Thread socket assembly through stem and into base; tighten.
Attach shade: Place fabric shade over socket and secure with locking ring.
Final check: Ensure all connections are tight and lamp stands upright.

CAUTION! Do not overtighten screws; handle fabric shade gently to avoid tears.

Specifications

Model: ARÖD 905.140.57
Type: Floor Lamp
Material: Metal base/stem, Fabric shade
Height: Approx. 140 cm (55 inches)
Bulb: 1 x E27 socket, max 13W LED or equivalent (not included)
Cord Length: 180 cm (71 inches)
Voltage: 120V AC, 60Hz (for North America)
Weight: 3.2 kg (7 lbs)

Installation & Setup

After assembly, choose location and install bulb.

Select location: Place on stable floor near power outlet.
Install bulb: Insert E27 bulb (max 13W LED) into socket.
Plug in: Connect cord to power outlet.
Test: Switch lamp on using cord switch or wall switch.

Tip: For optimal light distribution, position lamp in corner or beside furniture.

Operation

Lamp operates via inline cord switch or connected to a wall switch.

Switching: Flip cord switch to ON/OFF positions.

Brightness: Use with dimmable LED bulb and compatible dimmer switch for adjustable light (dimmer not included).

Usage: Suitable for ambient lighting, reading, or accent lighting. Do not use with wet hands.

Care & Maintenance

Unplug lamp before cleaning.

Metal parts: Wipe with dry or slightly damp cloth.
Fabric shade: Use soft brush or vacuum with brush attachment to remove dust.
Cord: Wipe with dry cloth; check for damage periodically.

CAUTION! Do not immerse in water; do not use abrasive cleaners or chemicals.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Lamp does not turn on	Bulb burnt out or loose	Replace bulb; ensure bulb is screwed in properly.
Flickering light	Loose bulb or incompatible dimmer	Check bulb connection; use non-dimmable bulb or compatible dimmer.
Lamp wobbles	Base not fully assembled	Tighten base-to-stem screw; ensure floor is level.
Shade uneven	Locking ring not secure	Adjust shade and tighten locking ring.
Overheating	Bulb wattage too high	Use only max 13W LED or equivalent bulb.

Reset: Unplug for 1 minute, then replug.

Warranty & Support

IKEA limited warranty applies; refer to IKEA warranty card for details. For assistance, visit IKEA store or contact customer support at 1-888-888-4532 (IKEA-USA). Online resources: www.ikea.com.

Recycling: Dispose of lamp according to local electronic waste regulations.