IKEA ARÖD 205.140.94 Floor Lamp instructions manual

The IKEA ARÖD 205.140.94 is a modern floor lamp featuring a sleek metal frame, adjustable shade for directional lighting, energy-efficient bulb compatibility (E26/E27 base, max 13W LED or equivalent), touch or switch control (model dependent), and a stable weighted base. It is designed for residential use in living rooms, bedrooms, or offices. Below are key sections for safety, assembly, operation, care, and troubleshooting.

Features at a Glance

Key components: Metal frame, adjustable lamp head, weighted base, lamp shade, bulb socket, power cord with inline switch or touch sensor.

Package Contents & Tools Needed

Unpack and verify all parts are included before assembly.

1. Package Contents: Base, pole sections, lamp head/shade, bulb socket assembly, screws/bolts, power cord, instruction manual.
2. Tools Needed: Phillips screwdriver (usually included), possibly a small wrench.

WARNING! Check for damaged parts before assembly. Do not use if any part is broken or missing.

Safety Instructions

Read all instructions before assembly and use.

1. Use only with recommended bulb type and wattage (max 13W LED or equivalent).
2. Unplug lamp before assembly, cleaning, or bulb replacement.
3. Place on a flat, stable surface away from heat sources and water.
4. Do not cover the lamp shade or allow fabric to touch hot bulbs.
5. Keep cord away from traffic areas to avoid tripping.
6. This lamp is for indoor use only.

CAUTION! Risk of electric shock. Do not disassemble beyond instructions.

Assembly Instructions

Follow steps in order. Assembly typically takes 15-30 minutes.

1. Attach Base: Insert the bottom pole into the weighted base. Secure with provided bolt(s).
2. Assemble Pole: Connect upper and lower pole sections if applicable, aligning holes. Insert and tighten screws.
3. Install Socket & Wiring: Thread the power cord through the pole. Connect the socket assembly to the top of the pole, ensuring wires are not pinched.
4. Attach Lamp Head/Shade: Secure the adjustable lamp head to the socket housing. Attach the shade to the head as per design (clip-on or screw).
5. Final Check: Ensure all connections are tight and the lamp stands upright without wobbling.

Tip: Do not fully tighten screws until all parts are aligned.

Specifications

• Model: ARÖD 205.140.94
• Type: Floor Lamp
• Height: Approximately 155 cm (61 inches)
• Base Diameter: Approximately 30 cm (12 inches)
• Bulb: 1 x E26/E27 base, max 13W LED or equivalent (not included)
• Voltage: 120V AC, 60Hz (for North America)
• Cord Length: Approximately 180 cm (71 inches)
• Materials: Steel, Plastic, Fabric
• Weight: Approximately 3.5 kg (7.7 lbs)
• Color: As per model (e.g., Black, White, Nickel)

Installation & Placement

Choose location carefully for optimal function and safety.

1. Select a flat, level surface near a power outlet.
2. Ensure the lamp is at least 1 meter away from curtains, bedding, or other flammable materials.
3. Plug the cord directly into a wall outlet. Do not use with extension cords or power strips if avoidable.
4. Adjust the lamp head to the desired angle after assembly.

WARNING! Do not place in high-traffic areas where it may be knocked over.

Operation & Controls

Operation is simple once assembled and plugged in.

Switch Model: Use the inline switch on the power cord to turn ON/OFF.

Touch Model: Gently touch the metal base or a designated area to turn ON/OFF. Some models may have multiple touch levels for dimming.

Adjustment: The lamp head can be tilted or rotated to direct light. Do not force beyond its natural stop.

Note: Allow bulb to cool before adjusting shade if lamp has been on for an extended period.

Bulb Replacement

Always unplug the lamp and let bulb cool before replacement.

1. Unplug the lamp from the wall outlet.
2. Allow the existing bulb to cool completely if it was recently on.
3. Depending on shade design, you may need to remove the shade by unclipping or unscrewing it.
4. Unscrew the old bulb counterclockwise.
5. Screw in a new E26/E27 base bulb, max 13W LED or equivalent (e.g., 60W incandescent equivalent). Do not exceed the recommended wattage.
6. Reattach the shade if removed.
7. Plug in and test the lamp.

CAUTION! Use only bulbs with the specified base and wattage to prevent overheating.

Care & Cleaning

Regular cleaning maintains appearance and safety.

1. Unplug the lamp and let it cool completely.
2. Wipe the metal frame and base with a soft, dry cloth.
3. For fabric shades, use a vacuum cleaner with a brush attachment to remove dust. Do not wash.
4. For metal shades, wipe with a damp cloth and dry immediately.
5. Never immerse any part of the lamp in water or use abrasive cleaners.

CAUTION! Do not use chemical sprays or solvents on any part of the lamp.

Warranty & Support

IKEA limited warranty applies. Refer to your IKEA guarantee for details.

For spare parts, assembly help, or product support:

• Visit: www.ikea.com
• Contact your local IKEA store.
• Refer to the IKEA app or catalog for part numbers.

Note: Keep your receipt as proof of purchase for warranty claims.

Troubleshooting

Safety First: If you suspect an electrical fault (burning smell, sparking), unplug immediately and contact IKEA support.

Service: www.ikea.com or your local IKEA store.