IKEA AKTERPORT 805.048.36 String Lights instructions manual

The IKEA AKTERPORT 805.048.36 is a decorative string light set designed for indoor use, featuring multiple LED bulbs on a flexible wire, a plug-in power adapter, and various hanging options. Below are key sections for safety, features, installation, operation, care, and troubleshooting.

1. Features at a Glance 2. Safety Instructions 3. Installation & Setup 4. Specifications 5. Controls and Operation 6. Hanging & Placement 7. Care & Maintenance 8. Troubleshooting 9. Warranty & Support

Features at a Glance

Key components: LED string lights, Power adapter, Hanging clips, Remote control (if included), Plug.

Feature	Description
LED Bulbs	Energy-efficient, long-lasting LED lights
Wire Length	Flexible wire for various arrangements
Power Adapter	Plug-in adapter for standard outlet
Hanging Clips	Included clips for easy mounting
Remote Control	Wireless control for on/off and modes (if applicable)
Weather Resistance	Designed for indoor use only
Modes	Steady on, flashing, or dimming options

Safety Instructions

Read all instructions before installation and use.

For indoor use only. Do not use outdoors or in wet locations.
Do not immerse in water or other liquids.
Keep away from heat sources, open flames, and flammable materials.
Do not overload electrical outlets or extension cords.
Unplug before cleaning, maintenance, or when not in use for extended periods.
Do not attempt to repair or modify the product. Contact IKEA for service.
Keep out of reach of children and pets to avoid entanglement or electric shock.

WARNING! Risk of electric shock. Do not use if cord or plug is damaged.

Installation & Setup

Unpack and inspect all parts. Ensure you have the power adapter, string lights, and hanging clips.

Plug the power adapter into a standard 120V AC outlet.
Connect the string light plug to the power adapter.
Arrange the lights in your desired pattern (e.g., along a wall, around a window).
Use the included clips to secure the wire. Do not use nails or staples.
Turn on using the switch on the adapter or remote control.

CAUTION! Do not stretch or bend the wire sharply to avoid damage.

Specifications

Model: AKTERPORT 805.048.36
Bulb Type: LED
Number of Bulbs: 20 (or as per product)
Cord Length: 10 feet (approx.)
Power Source: 120V AC, 60Hz via adapter
Input Voltage: Adapter input: 120V AC
Output Voltage: Adapter output: Low voltage DC (e.g., 12V)
Light Modes: Steady, Flashing, Dimming (if applicable)
Indoor Use Only

Controls and Operation

Power adapter: On/Off switch. Remote control (if included): On/Off, Mode selection, Timer.

Operation Steps:

Plug in the adapter and turn on the switch.
Use the remote to select light mode (steady, flash, dim).
To set a timer, press the timer button (if available) for auto shut-off.
To turn off, use the remote or switch on the adapter.

Note: Remote requires batteries (typically AAA). Replace if unresponsive.

Hanging & Placement

Use only the included clips for hanging. Avoid placing near curtains, bedding, or other flammable materials.

Plan your layout before hanging.
Attach clips to the wire at desired intervals.
Secure clips to surfaces using adhesive backing or small nails (if designed for).
Ensure the wire is not taut; allow some slack.
Do not run wire under carpets or in high-traffic areas.

Tip: Test lights before final hanging to ensure all bulbs work.

Care & Maintenance

Unplug before any cleaning. Use a dry, soft cloth to wipe the wire and bulbs. Do not use liquids or abrasive cleaners.

Storage: Coil the wire loosely. Store in a cool, dry place away from direct sunlight.

CAUTION! Never pull the wire to unplug; grasp the plug directly.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Lights not turning on	Power outlet issue, adapter not connected	Check outlet; ensure adapter is plugged in securely; try another outlet.
Partial lights out	Loose bulb, damaged wire	Check and tighten any loose bulbs; inspect wire for damage.
Remote not working	Dead batteries, obstruction	Replace remote batteries; ensure clear line of sight to adapter sensor.
Lights flickering	Loose connection, adapter issue	Check all connections; ensure adapter is fully plugged in.
Adapter warm/hot	Overuse, ventilation issue	Unplug and let cool; ensure adapter has airflow; do not cover.

Reset: Unplug adapter for 30 seconds, then reconnect.

Warranty & Support

IKEA limited warranty applies. For product support, contact IKEA customer service or visit www.ikea.com.

Service: 1-888-888-4532 (IKEA US); www.ikea.com